Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket CAN bus immobiliser. It's subtle, doesn't have key fobs or LED indicators and is hidden within the wiring of the vehicle.
The user may also turn off the system for a short period of time by using Transport Mode when renting out their car. This guide will guide you through the process of installing an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a modern security device that guards your vehicle from hacking, key cloning, and relay attacks. The system is linked directly to the ECU of your vehicle and secured by a PIN code that you choose. It is inaccessible to thieves using scanners for diagnostics or other modern methods, and is unable to be disabled by cutting circuits.
The system is simple to use, however professional installation is recommended to ensure a clean connection to the ECU of your vehicle. Installers who are approved by Thatcham can assist you with the installation and programing of your Ghost system. They can also recommend a tracking or alarm system to complete the protection package for your vehicle.
First, the installer must disconnect your battery to prevent accidental airbag deployment or short circuits. After the battery has been disconnected, the installer may safely begin working. Hand tools are the most basic to be used to ensure precise connections. A multimeter is useful to check electrical values. Insulation tape and cable tie are crucial to ensure connections are secure and keep wiring neat. Lastly, the user manual gives specific guidelines that are specifically tailored to your Ghost Immobiliser model.
During the installation process, it's important to choose the right grounding location that is free of any paint or debris. Installers should also ensure that the immobiliser's wires CAN H and CAN L are connected to the proper ECU ports. Based on the model, these wires might need to be soldered or plugged in. To ensure a reliable and long-lasting connection, it is recommended that you choose a top-quality plug.
Once the install is complete After the installation is complete, the customer can turn on Transport Mode. This allows the vehicle to be used by valet parking or mechanics without needing to know the pin code. The user must press the service icon on the dashboard five times over 2 seconds. The system will confirm this by showing 5 indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's a smart option for those who regularly rents out their cars on platforms such as Turo. An immobiliser can cut down on insurance rates, as it decreases the likelihood of theft.
Getting Started
If you are looking for a solution that will secure your vehicle from thieves You can't go wrong with an autowatch ghost immobilise r. The device protects your vehicle from being started the theft or copies the key. It's possible because of its advanced technology that prevents the engine from starting until the right PIN code has been entered.
The device is connected to the vehicle's bus system CAN, allowing direct communication with the ECU. It makes use of the buttons on your dashboard and steering to create a unique sequence that only you can understand. This makes it impossible for anyone else to start your car. This is the ultimate security system that will safeguard your pride and joy and preserve its value when you want to sell it in the future.
Installing Ghost's immobiliser is straightforward however, you must follow the instructions to avoid electrical issues and system malfunctions. You'll need to locate a 12V power supply and a suitable grounding for the chassis of your car. Then, you can start connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering methods to ensure a strong connection. Also, ensure that you cover the connections by using heat shrink tubing or insulation tape to shield them from electrical short circuits and other issues.
After the wires are connected, you can plug in the battery and begin the engine to check if the immobiliser is working. Once you have verified that everything is functioning properly, you can install the immobiliser in a safe location in the vehicle. Make sure you hide it well to prevent any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified, which means that it meets the highest standards of security and is a great protection against car thieves. It is invulnerable to key cloning and hacking and is not able to be disabled without the code. The device is also simple to use and is able to be put into the service valet mode to ensure that your vehicle will not be activated when you bring it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system that is designed to stop theft of vehicles. It communicates with your vehicle's ECU and directly connects to the CAN bus. Unlike other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with your vehicle's factory settings.
It's also completely undetectable to thieves using diagnostic scanners. This is due to the fact that it doesn't send and receive radio frequency signals, and it uses the CAN data to communicate with your ECU. It doesn't even require any modifications to your existing key fobs.
Enter your sequence for disarming (either two or one button) and then switch on the ignition of your car to use Ghost Immobiliser. love it will flash two times to confirm that you have entered the correct code. Once you've verified this, you're able to start your car and drive away with peace of mind.
Once installed, Ghost Immobiliser safeguards your vehicle against hacking or key cloning, while preserving its value. In Transport Mode, you can temporarily disable the Ghost Immobiliser if you have to hand your car over for service or valet park.
You'll need a constant power source (12V) as well as a grounding source to complete the installation of the Ghost immobiliser. Be sure that both are properly insulated and can be touched. Cable ties are also suggested for bundling and securing the wires. This will reduce the possibility of theft by potential thieves. Be sure to check the exact position of these points to avoid mistakes, and mark them with a piece of tape or label. It's recommended to examine all connections for signs wear and tear. Make sure all connections are firmly in place, and properly sealed. Finally, don't forget to test the Ghost Immobiliser after installation is complete. This will ensure that the unit is operating properly and that all connections and insulation are safe. If there are any issues, you must be sure to resolve them immediately.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that connects seamlessly with your car's ECU to prevent the motor from starting without authorization. Its innovative technology protects your vehicle from key cloning and hacking and other common tactics that thieves employ to steal vehicles. The Ghost also works in tandem with existing alarm and tracking systems to offer the best protection for your vehicle. The Ghost's unique features and discreet design make it a popular option for car enthusiasts and security-conscious drivers alike.
It is essential to follow the procedures for installation to ensure a correct integration of the Ghost Immobiliser. Check the wiring diagram of the vehicle to assist you in locating and connecting the wires. You'll need to determine the grounding and power sources. Once you've found them, you'll have to mark them in a way that they're easily identifiable during the installation process. It's essential to use high-quality materials and tools. Basic hand tools can help in making connections that are precise while a multimeter can check electrical values and ensure security. Insulation tape and cable ties will help keep all connections tidy and neat. Finally, a user manual will provide specific instructions specific to your Ghost model.
It is crucial to test the system prior installing it. Enter the PIN code into the system and then start the vehicle. This will ensure that the immobiliser works according to plan, and prevents unauthorised vehicle start-ups. This step should be done regularly as part of your routine inspections of the vehicle to ensure that the system is working properly.
Once the installation is complete After the installation is completed, you are able to drive your car with confidence. The Ghost will protect your car from potential car thieves. It will ensure that no one can take your car away even if they don't have the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker that detects any attempts to steal or tamper with. This lets you track your car in the event that it's stolen.
The Ghost is compatible with a range of automobiles, including those from the majority of major manufacturers. If you are interested in securing your car with this cutting-edge device, contact Monty's Locksmith today to find out more about our installation and maintenance options. We are a TASSA Installer who is registered which guarantees that we adhere to the strictest guidelines and procedures when installing our products. This assures customers insurance companies, customers, and law enforcement agencies that all installations are performed safely and correctly.